If you have lots of room and can easily make large, round bends; you won’t need elbows. If you’re in a smaller space though, they will save you lots of room and prevent kinking. See the pictures here for examples of using them to go up and down in raised beds.
Be the first to review “Blumat 8mm Elbows”
|Settings||Blumat 8mm Elbows remove||BluSoak Drip Tape 10' Plant Ring - Ready to Connect to a Blumat Sensor remove||3/4" Female Hose Thread (FHT) to 8mm Barbed Insert - Garden Hose Adapter remove||3mm Blumat Tees remove||Blumat Standard Pressure Reducer 1bar (15psi) remove||Blumat 8mm Shut off Valve remove|
|Name||Blumat 8mm Elbows remove||BluSoak Drip Tape 10' Plant Ring - Ready to Connect to a Blumat Sensor remove||3/4" Female Hose Thread (FHT) to 8mm Barbed Insert - Garden Hose Adapter remove||3mm Blumat Tees remove||Blumat Standard Pressure Reducer 1bar (15psi) remove||Blumat 8mm Shut off Valve remove|
|Price||$1.10 + Tax||$11.00 + Tax||$6.00 + Tax||$1.10 + Tax||$50.75 + Tax||$4.85 + Tax|
42 in stock
3 in stock
Out of stock
17 in stock
3 in stock
Out of stock
|Availability||42 in stock||3 in stock||Out of stock||17 in stock||3 in stock||Out of stock|
|Add to cart|
|Content||If you have lots of room and can easily make large, round bends; you won't need elbows. If you're in a smaller space though, they will save you lots of room and prevent kinking. See the pictures here for examples of using them to go up and down in raised beds.||The BluSoak Drip Tape 10' Plant Ring is a pre assembled unit ready to be connected to your Blumat sensor and is ideal for larger pots that need more water coverage. A 10' soaker hose ready to plug into a Blumat sensor - just push the tubing into the Blumat output hose and wind around the area you'd like to keep moist. Distribution drippers are less expensive in small pots, this one less expensive in larger ones. Keeping more of the potting mix moist lets more roots grow and in effect gives you a much larger pot for the same pot and planting mix cost. This product comes with: 1 BluSoak to 3mm adapter 1 BluSoak End Plug 1 Distribution Dripper 10' of BluSoak 2.0 Drip Tape||Conventional Garden Hose Adapter for a 3/4" Female Hose Thread to 8mm Barbed Insert, easiest way to connect your 8mm tubing to a conventional hose or any 3/4" male hose outlet. Extremely hard to find anywhere but we managed to find it internationally and have it shipped to us. This is product to save you a hardware trip, added to our website for your inconvenience.||Use these to branch out and run distribution drippers in two directions. You can also put them directly into a 1/2" or 3/4" drip line and install two Blumat sensors.||TRUE REDUCER - Not a mere flow controller, this brings water pressure down to 15 PSi (1 bar)! EASY TO INSTALL - Screws onto standard hose thread (3/4" input), and ouputs to 8mm tubing! ENDURING - Made from ABS plastic and designed with few points of failure, this is built to last! BLUMAT-READY - Designed specifically for blumat watering systems and 8mm tubing, no tools necessary! AUSTRIAN-ENGINEERED - This high-quality component is designed and manufactured by clever Austrians! Blumat systems need low pressure, much less than comes from normal house water connections. The blumat Pressure Reducer allows for easy integration of a municipal (or otherwise pressurized line, such as from a well) water line into a blumat, blusoak, or easysoak watering system. BEWARE IMPOSTERS! Many pressure reducers are not real pressure reducers at all, but are merely flow controllers, and reduce flow rates. However, reduced flow rates DO NOT necessarily correlate to reduced pressures. This is a true pressure reducer, and will reduce any incoming water (with a maximum pressure input of 87PSi) down to a 15PSi (1 bar) output. This is ideally suited and low enough for blumat systems and their components. Higher pressure will push tubing connections apart, and increase likelihood of flooding. This pressure reducer is extremely easy to use. The input side screws onto a standard 3/4" hose bibb or hose threading, often found on taps outside the home, or even faucets inside the home. The output side (featured with collar) is ideally suited for 8mm tubing (I suggest using our super-flex tubing). This is the size that integrates directly with tropf blumats. This adaptation makes setting up a blumat system from a hose or pressurized line an absolute breeze, and you can install your blumats in seconds. Blumat systems need low pressure, much less than comes from normal house water connections. Some of our kits include one of these but if you'd like to install the other ones or the separate components to a home water system, you'll need one of these Pressure Reducers. In gravity systems you'll also need one if your storage tank is high uphill. In Grow Rooms and Greenhouses with a reservoir for mixing nutrients, you can connect a small pressure pump to this and automatically feed your plants when you water. On one side it adapts to a 3/4" male hose thread and on the other directly to the Blumat 8 mm supply tube. Maximum input pressure is 87 psi.||These shut-off (or on/off) valves from Blumat brand are the quarter-turn valves you've been looking for! These valves are ideal for blumat watering systems. They can be installed in-line in any 8mm tubing, but we recommend super-flex. Simply remove the collar, and place the collar over the 8mm tubing. Then slide the tubing over the 8mm barb, screw on the threaded collar, and you are in a perfect position to irrigate your plants!|
There are no reviews yet.